mksilikon.blogg.se - Elkay touch timer

#ELKAY TOUCH TIMER HOW TO#
#ELKAY TOUCH TIMER PLUS#

Remove the sealant and use Teflon tape or a compression fitting. If your water cooler is newly installed, then the water pressure in your building might simply be lower than factory test conditions.If water cooler was manufactured prior to 2001 and water is also very cold, the evaporator may need to be replaced.Įlkay Water Cooler Troubleshooting Water Stream from Bubbler is Too Lowīelow is a numbered list of the most popular potential causes of low flow bubbler stream along with corrective actions to take to troubleshoot them. Water line inside of water cooler is kinked.You will know this is the cause of no water flow is compressor and fn are not working and everything is connected and plugged in). Reconnect correct wire to solenoid valve. Wire disconnected from solenoid valve.No Water Flow in EZ, HTV, or electric eye operated water cooler models: Insert screen back onto solenoid valve and make sure o-ring is placed properly.Įlkay Water Fountain Troubleshooting Bubbler Water Stream and FlowĮlkay Water Cooler Troubleshooting No Water Flow Remove the screen and rinse thoroughly with water.

To clean the strainer, unscrew the solenoid valve cap. Then simply reassembly and replace the top section of the mat.Remove the top section of the mat, and spray the fill mat with a mild dishwashing soap and wipe down with a microfiber (or equivalent) towel, making sure to also wipe down underneath the mat, and the top section of the mat that you removed earlier.Remove the four screws that sure the flexible fill mat.How do I clean the ezH2O flexible fill mat? Replace the top cover and your filter status reset is complete.

At this point, the filter status light should change back to green when correctly reset.

When the following message shows on the screen: ‘RST FLTR’ (shown in the image below), press the black reset button in the top right side of the inside of the unit again.

Different messages will flash across the LED interface.

Press the black reset button located in the top right side, holding for about two seconds before releasing.

Remove the top cover of your ezH2O unit.

*The directions below are for units with an LED bottle filler counter. How do I reset my Elkay ezH2O bottle filler filter status?

If you have the filter status LED light on the top portion of your cooler, (this will exist on all newer versions of Elkay ezH2O combination water cooler bottle filler units) then you need to reset your filter status to green.

(Note: there is no need to turn off the water when replacing your Elkay ezH2O water filter.)

#ELKAY TOUCH TIMER PLUS#

Replace it with the new Elkay WaterSentry Plus filter.

Remove the bottom access panel from the lower portion of the water cooler (the panel below the push buttons).

When the filter status turns red, or when you know that the filter is due to be replaced then proceed in changing the filter.

How do I change the filter on my Elkay ezH2O cooler? We recommend paying extra attention to the bubbler, push buttons, and other areas of the cooler that are often touched by users. How should I maintain my Elkay water cooler units?Įlkay recommends using a soft cloth (we think microfiber would work well) along with mild dishwashing soap to spray and wipe down the unit.

How often depends greatly on a number of factors, including how much traffic your fountain gets, where your unit is located, and water quality. How often should I clean my Elkay water cooler unit?Įlkay recommends continuous cleaning in maintaining your Elkay units.

#ELKAY TOUCH TIMER HOW TO#

Learn how to properly clean your units as per Elkay’s recommendations, plus how to replace the Watersentry filter in your Elkay water coolers as well as reset the filter status for your units both in this quick Q&A style Elkay troubleshooting and maintenance guide. The seamless design of Elkay ezH2O makes them easy to install, keep clean, and properly maintained, with a little bit of attention and care. This article contains some of the most common Q&A’s pertaining to Elkay ezH2O troubleshooting and maintaining commercial water cooler and bottle filler units.